How I leared what a decoupling capacitor is for, the hard way

4/28/2026 at 5:13:38 AM

Ah how things have changed. When I was learning electronics we mainly dealt with radio and TV circuits and just about the first lesson one learned was to keep leads short (reduce unwanted inductance) and use decoupling capacitors everywhere.

I recall some years later a young graduate engineer coming into my office with a rather involved circuit consisting of 30/40 TTL ICs and complaining that he'd double checked the circuit and it still didn't work. I took one look at his device then went to the draws of capacitors and handed him a handful of 0.1uF ceramic caps and told him to put them between the ICs' PS rail pins to ground which he did and to his amazement the circuit worked immediately.

He stood in amazement that I should have such insight so as to fix the problem at first glance.

How such critical knowledge can get lost in university training these days just amazes me.

by hilbert42

4/28/2026 at 7:06:59 AM

My university made us use really crappy power supplies and dev boards. Nothing worked unless you first put a large bulk capacitor on the power supply's output, and small capacitors close to the components.

Also I got bitten by parasitics in capacitors very early in my career: capacitors of different face value will resonate with each other to effectively kill the decoupling network at a specific frequency (resulting, for me, in an amplifier with a nice hole in its frequency response).

by lefra

4/28/2026 at 11:28:02 AM

Incidentally, in my post below on the MIT RadLab series I mention Vol 23. On p183 parasitic oscillation is mentioned. Also, I recall when working in the now defunct RCA prototype lab, one of the main cure-alls for parasitic oscillations was to place a ferrite bead on a transistor lead (between it and the PWA). It often worked wonders.

by hilbert42

4/28/2026 at 7:45:14 AM

Excellent training, especially the parasitic bit. Trouble is somehow many aren't taught that stuff nowadays.

by hilbert42

4/28/2026 at 9:13:48 AM

Sounds like an opportunity to build a shenzhen i/o prequel

by baq

4/28/2026 at 6:41:49 AM

I feel it’s a function of abstraction.

You learned when analogue circuitry was the norm. I learned when digital circuitry was simple enough that you could readily take something apart and understand it.

Now, EE courses often start with cad, simulations, digital electronics, and you end up with people building ziggurats atop an ocean of incomprehension.

It’s exactly the same thing with software.

I don’t scorn people for this, rather I see myself as fortunate for having learned in a time when the more fundamental knowledge was still worth learning - and that’s the rub - for a vast majority, it simply isn’t worth the time or energy to explore the full stack, when there’s so much to learn atop it.

by madaxe_again

4/28/2026 at 7:21:45 AM

"You learned when analogue circuitry was the norm. I learned when digital circuitry..."

What's not taught properly these days is that ALL electronics is analog at the physical/circuit level.

For you digital types that's OSI Model Layer 1 — Physical layer (look it up on Wiki). Nothing in electronics works unless that's working properly—ICs, tunnel diodes, transistors, inductors, resistors, capacitors, cables and antennas are all analog devices at that level. That includes the heart of the most advanced digital ICs. For example, the upper clock speeds in processors are limited by transit times/electron mobility, inter-electrode and stray capacitances, unwanted inductance, etc.—all of which are analog effects and they must be accounted for.

Like it or not, the physical analog world is alive and well! The Noughts & Ones Brigade unfortunately seems to have forgotten that fact.

by hilbert42

4/28/2026 at 10:36:09 AM

> you end up with people building ziggurats atop an ocean of incomprehension.

Everyone does. There's probably a layer below for everyone but the most theoretical physicists. I don't know where the leaks in electronics engineering's abstractions are, but I'm pretty sure they exist.

by vintermann

4/28/2026 at 10:03:13 PM

This is why I went on to study physics - I never was someone who could stop asking “why?”

All it does is provide yet more profound questions.

by madaxe_again

4/29/2026 at 10:50:52 PM

"…I never was someone who could stop asking “why?”"

When a kid of about four I found a pair of WWII headphones and took them to my father who pulled out the iron diaphragm and showed me magnetism at work—somehow some magical force was pulling the diaphragm back into the headphone with seemingly nothing in between. Absolutely fascinated, I wanted to know what this invisible 'magic' was. Many decades later every time I look at my fridge magnets I still ask the same question and I don't believe I'm much closer to the truth!

Sure, there are the simple answers everyone's taught, then there's QFT but even that doesn't tell me exactly what's going on. And why does alpha have the value it does, and why exactly does c = 1/(μ0ε0)^1/2? Not knowing and not being able to figure these questions out is, at times, infuriating.

For me, solace of sorts can be found in engineering—I can build an electronic circuit and end up with a tangible working device. On the way I'll curse my electrons for making so much noise that they sound like ball bearings rattling around in an empty oil drum but I'll eventually calm down and apply Johnson–Nyquist to shut them up (well, a little bit anyway).

by hilbert42

4/28/2026 at 1:54:39 PM

Well... https://xkcd.com/435/

by sdenton4

4/28/2026 at 6:55:33 AM

> How such critical knowledge can get lost in university training these days just amazes me.

It will probably have been taught.... but very briefly. Before going go back to analysing circuit schematics, where connections between components don't show resistance or inductance, and the capacitance of two parallel capacitors sums.

by michaelt

4/28/2026 at 7:16:04 AM

This is why lab exercises are important. I remember first building some actual TTL circuits on bread board, I learned very quickly that this whole digital stuff is a lot uglier and messier than on paper or in the simulator.

With sharp rise times, synced up to a common clock, even after soldering in a whole bunch of capacitors, you can still stick a probe pretty much anywhere and see switching spikes all over the place, from power rails to completely unrelated signals that are supposed to be stable. Using actual TTL, there was another funny lesson what this weird "fanout" value in the datasheet meant.

A similar lesson I learned that way (and a very memorable one :-)) was about flyback diodes.

by st_goliath

4/28/2026 at 7:30:35 AM

Ah, but that may well be because of your scope probe's leads! The sharper the edge the more likely that will happen. That's what those shitty little springs are for that come with your scope probe: you disconnect the ground wire and put that spring on the naked scope probe pin around the ground collar. Then where you want to measure you use the pin to go to the signal and the little spring to reach the nearest ground. Presto: clean signal (or at least, much cleaner). Also, make sure to tune your probe (that's what the little plastic screwdriver with metal tip is for, there is a small trimmer in the probe you can reach through a hole and that is critical at high frequencies) and avoid probes with switchable 1/10 like the plague, over time the switches go lame and then you'll be tracking all kinds of weird gremlins.

by jacquesm

4/28/2026 at 8:11:56 AM

This is just reminding me of the time I played with an oscilloscope, touched the probe against my finger and found my body was antenna picking up mains frequency.

by ben_w

4/28/2026 at 8:36:45 PM

> or in the simulator

Inadequate simulator, then, no?

(I imagine analogue RF board-level simulation is a lot more expensive than digital-logic board-level simulation. Might have been impractical way back when, such that we only used to have the digital-logic kind. But we certainly have both kinds today.)

by derefr

4/28/2026 at 12:21:10 PM

I've struggled to find a proper introductory guide to stuff like this. Moving from pre-made Adafruit boards to my own PCBs was very tough to navigate; every guide I came across assumed you knew all sorts of stuff that the EEs writing them probably committed to deep memory decades earlier.

by ceejayoz

4/28/2026 at 12:45:47 PM

I found Phil's lab content [1] [2] indispensable for just this. Phil is a great communicator and gives in-depth explanations, so I didn't just watch most of his youtube, but also bought his mixed signals course and was very happy with it.

Phil also recommends this lecture in one of his videos [3], which is still one of my all time favourite lectures ever.

[1] https://www.youtube.com/@PhilsLab

[2] https://www.phils-lab.net/

[3] https://www.youtube.com/watch?v=QG0Apol-oj0

by dgroshev

4/28/2026 at 4:19:41 PM

Fantastic stuff, esp. #3 which I had not seen before. Thank you.

by jacquesm

4/28/2026 at 12:02:13 PM

I have an MSEE from a top university (from 20 years ago), this topic unfortunately is not really taught. The theory and analysis is taught, but the practical implications were not. I connected the dots in my first job out of school where some very talented gray beards taught me how the real world works. Which brings me to my point that EE really is a trade. It takes schooling at the beginning and in most cases a degree or two, but there is critical knowledge that you learn in the real world after school; and there are levels analogous to apprentice, journey man, and master.

by InUrNetz

4/28/2026 at 6:03:15 AM

I can see how that happens when people come at things from a conceptual digital side first.

It probably doesn't help when you have a circuit diagram that while topologically correct doesn't show the relative positioning between components. The first time I saw all the decoupling caps rendered in a single chain on the side of the diagram I was mightily confused. It seemed like utter nonsense until I realised where they actually went.

by Lerc

4/28/2026 at 9:42:20 AM

"The first time I saw all the decoupling caps rendered in a single chain on the side of the diagram I was mightily confused…"

If you've read my other comments here you'll realize I'm concerned that these days EE training doesn't place a strong enough emphasis on shielding, ground loops, decoupling and such that it ought to. For any electrical/electronic engineer these are critical concepts.

By way of stressing that I'd like to take a sojourn into history and refer you to probably the greatest set of electronic engineering books ever produced: the MIT Radiation Laboratory Series — a massive 28 volume set written nearly 80 years ago to document electronics and microwave/radar research done during WWII.

Anyone seriously interested in electronics should be aware of this series. Yes, it's dated, heavily weighted towards vacuum tube technology (although klystrons and magnetrons are still current), and it lacks modern semiconductor tech, however this truly remarkable set contains a huge amount of information that's still very relevant today. Moreover, whilst it covers the topics in depth it does so at a level that can be easily understood by undergraduates (explanations are more general than today's very specialized textbooks).

https://en.wikipedia.org/wiki/MIT_Radiation_Laboratory_Serie...

Here you'll find links to the Internet Archive where the volumes can be downloaded. Specifically, I would refer you to Volume 23 - Microwave Receivers, — Chapter 6 Intermediate Frequency Amplifiers p155. Now turn to p182 and read 6-10 Practical Considerations.

Here's the PDF of V23:https://archive.org/download/mit-rad-lab-series-version-3/23...

This section on decoupling, shielding etc. is just as applicable to today's high speed digital circuits as it was back in WWII. Sure it needs updating but the fundamentals of screening and decoupling have not changed. What's important here is that these physical (analog) effects are set by the fundamental laws of physics, and circuits that do not take them into account will fail to work correctly.

by hilbert42

4/29/2026 at 8:38:22 AM

> It seemed like utter nonsense

This is utter nonsense. Just ask the layouter where they will be placed. (at the output of the voltage regulator or where he will find empty space on the board, completely missing their function). Where your schematics is bad, the layout will be also bad.

by hulitu

4/28/2026 at 7:27:32 AM

https://xkcd.com/1053/

by amelius

4/28/2026 at 5:35:22 AM

This is probably a good place to debunk the usual wisdom that "decoupling capacitors must be placed very close to the IC pins". If you're using a solid power plane, rather than routing power through traces (and honestly 4/6 layer boards are cheap enough these days) it really doesn't matter where you place decoupling capacitors for most uses - keep the via traces short or ideally in the pad, and you can put all your decoupling capacitors in one place on the boards a way away from the chip and focus on good routing of your signals. Figure 15 on this paper (and the whole paper!) explains it well: https://scholarsmine.mst.edu/cgi/viewcontent.cgi?article=221...

by nippoo

4/28/2026 at 7:03:44 AM

Loop inductance is what really matters with decoupling. Once you understand that, it becomes really easy to make good decisions. This article explains how you can approximate the inductance for a given layout, so it makes evaluating layouts much simpler. It actually used the data from the paper you referenced in example 3!

https://learnemc.com/estimating-connection-inductance

You can even use mutual inductance of vias improve performance, either by having vias spaced close together and in the right order (https://learnemc.com/decoupling-for-boards-with-widely-space...), or arranging capacitors in alternating or doublet layouts (https://incompliancemag.com/decoupling-capacitor-design-on-p...).

As you say, just having power planes and directly connecting to them is almost always going to be superior to using a trace, despite seeing this all the time, especially in datasheet example layouts. It made sense for 2 layer boards, but not today. Just think, the inductance of the planes is practically zero, and distance to the plane from the components is going to be on the order of 0.2mm, round trip 0.4mm. Is there any way I could place the capacitor 0.4mm away from the pins to achieve an equivalent inductance? And even if you could, you can't add extra vias to lower inductance, and you don't benefit from mutual inductance.

by fps-hero

4/28/2026 at 8:23:12 AM

Yeah

The ELI5 for decoupling capacitors is "imagine an energy storage for quick usage"

The ELI(tired EE student) is more like the explanation above

And this concept is ok for most of the 'low speed' circuits

in RF ranges, everything is a capacitor (except when you need one), everything is an inductor (except when you need one) and the intuitive explanations break down and everything looks like dark magic

by raverbashing

4/28/2026 at 11:52:54 AM

I love your reverse psychology analogy. That does make me wonder, if a cap past its SRF is an inductor, and and inductor past its SRF is a cap, why not swap caps for inductors and vice versa, put an amplifier on the end and call it a day!

by fps-hero

4/28/2026 at 3:41:29 PM

You can't, because all amplifiers oscillate (except when you need an oscillator).

by lefra

4/28/2026 at 2:28:11 PM

And every wire or PCB trace is an antenna, broadcasting and/or receiving whatever it has access to, at its own particular frequencies.

Across distances according to the power available, where ariel orientation makes a big difference, "as expected".

by fuzzfactor

4/28/2026 at 12:45:18 PM

Explanations like that are a lot easier to understand if you can see the equivalent circuit with the parasitic components.

by amelius

4/28/2026 at 9:48:58 AM

Well, till it does. Paper talks about frequencies in 200MHz range, not every project can afford solid power planes and putting it next to a chip costs literally nothing. It's like safety helmet, 99.9% of the time it's not needed

by PunchyHamster

4/28/2026 at 6:44:51 PM

Above 400MHz or so, the on-die/on-chip capacitance starts being the most important thing (you're going to have inductance through the legs or balls of the chip).

Putting your decoupling capacitors next to the power pins _does_ cost. Not just in board space, but I've seen and reviewed layouts where the signal traces had to snake around decoupling caps or in some cases through vias because the designer believes that putting the caps close to the pins was the most important thing...

by nippoo

4/28/2026 at 6:04:17 AM

Great paper!. Anyonw know whether there are any modern tools/software that can simulate this during design?

by laydn

4/28/2026 at 6:54:52 AM

For approximative simulation, any SPICE simulator works. You'll need to know your capacitors parasitics and power supply output impedance, find a typical via's impedance, and manually compute traces impedances and board capacitance.

For accurate simulation, the actual board geometry needs to be fed to a simulator that'll compute the actual impedances. Last I checked only Very Expensive Software could do that in a user-friendly way (I had to route a DDR3 bus. I ended up being very cautious so that all traces had the same topology and the same lengths, and cross my fingers. It worked).

If anyone knows of free alternatives for that, I'd be interested to hear about it.

by lefra

4/28/2026 at 3:47:43 AM

This signifies that each vertical dotted line is 20ns apart, so the ripple you see has a frequency of something like 50MHz.

Unless you have a 50MHz buck converter (which would be very exotic --- the fastest common ones are around 1/10th that), that looks more like something may be inadvertently oscillating and/or you're picking up strong RF noise from possibly something in...

https://en.wikipedia.org/wiki/6-meter_band#Radio_control_hob...

And "leared" -- the (unintentional?) pun made me click.

by userbinator

4/28/2026 at 6:26:05 AM

It's not oscillating at 50MHz. Look at the waveform, with the big spike in the middle. That's a spike at some lower frequency, wider than the screen, followed by ringing. Need to zoom out the time base some more to see the period of the big spikes. It's no higher than 4 MHZ (the screen is 12 units wide) and possibly much lower. (Assuming that M:20ns on the display means 20ns/grid division. The manual is a bit hazy on that part of the UI.)[1]

The power regulator IC mentioned is normally run at 500KHz. There's a reasonable chance that this is the power regulator spike not being damped out. Easy enough to check with a scope handy.

[1] https://fotronic.asset.akeneo.cloud/pdfs/media/owon_hds242s_...

by Animats

4/28/2026 at 4:23:59 AM

>And "leared" -- the (unintentional?) pun made me click.

I assume it's a reference to the "Quality Learing Center" in Minnesota, one of the questionable daycares at the center of the alleged Somali daycare fraud scandal. Ever since some of the expose videos about it came out it's become a meme to say "lear" instead of "learn".

by JCTheDenthog

4/28/2026 at 6:44:23 AM

> questionable daycares

If they don't find fraud, is it "questionable"?

by nielsbot

4/28/2026 at 12:38:34 PM

Didn't the guy flee the country after posting bail? Doesn't exactly scream "innocent".

by bavell

4/29/2026 at 12:55:31 AM

I didn’t see that. Is there a source? I saw Minnesota authorities investigated the business and didn’t find evidence of fraud.

I did read there was some amount of fraud in state sponsored care programs but nothing extensive.

by nielsbot

4/28/2026 at 10:12:42 AM

If they choose not to look, yes.

by peterfirefly

4/28/2026 at 4:16:57 AM

Cannot it be a noise from imperfect switching? The switching occurs at lower frequency, and the noise is high frequency.

by codedokode

4/28/2026 at 6:18:52 AM

I guess he also believes that 50 MHz or so signals can be measured reliably on a 40 MHz (on paper at least) scope.

by elch

4/28/2026 at 9:51:07 AM

Most digital scopes have around 5-10 times faster sampling than bandwidth. The one on pic is 250Msps.

That's more than good enough for the purpose of checking interference

by PunchyHamster

4/28/2026 at 10:06:48 AM

But he tries to quantify this interference. Anyway Animats's comment is the one that points IMHO to the most likely cause of the observed waveforms.

https://news.ycombinator.com/item?id=47931024

PS Now that I’ve taken a closer look, this is even sillier than I first thought.

He’s hunting for 50 MHz ghost signals by connecting his PCB to a breadboard using (crappy) wires that are at least 10 cm long. And he’s connecting the scope probe to the breadboard (or those breadboard wires).

And if I’m not mistaken, he doesn’t even bother to connect the ground lead of the probe.

by elch

4/28/2026 at 1:05:22 PM

Slightly related note, the pictures in the articles show a handheld digital oscillscope. It's an Owon HDS200 series oscilloscope with signal generator and they are amazing and the lower frequency models are quite inexpensive.

I got myself one earlier this year and it does what it says on the tin. It can also be controlled from a computer via USB serial connection using a text based protocol (albeit poorly documented and a bit buggy). I used some python scripts to program the signal generator and then capture some measurements from the scope to check the frequency responses of some analog electronics circuits for guitar.

There is a small community around, there are a few repos on GitHub for using them and also this very long eevblog thred.

https://www.eevblog.com/forum/testgear/owon-hds-200-handheld...

by exDM69

4/28/2026 at 1:27:42 AM

Having 1.5V Vpp ripple on a 3.3V supply rail seems more like an issue with the regulator / bulk capacitance than a decoupling capacitor, I would think?

by hadrietta

4/28/2026 at 1:44:15 AM

Yea since writing this I think it has more to do with the regulator circuit. I plan to do a small rewrite and change the title to something like "When 3.3V isn't actually 3.3V" to more accurately reflect the situation. A decoupling cap would probably still help, but there were some mistakes made on the regulator circuit.

by actinium226

4/28/2026 at 1:49:56 AM

Switching regulators (and even linear regulators!!) have maximum capacitance ratings.

Adding more capacitance could, in theory, further destabilize your regulator.

The overall tank circuit (the inductor + capacitor forming the bulk of the switching circuit) is incredibly fragile.

It's legend that some old switching designs stopped working as newer tantalum capacitors had less resistance, screwing with the stability of older switching designs. You kind of need to choose exactly the "expected" kind of capacitor (aluminum caps have more resistance, which increases stability of the feedback but slows down the feedback).

by dragontamer

4/28/2026 at 1:31:23 AM

Yeah. Decoupling capacitors are for smaller ripples than that.

There might be a resonnance point on that regulator, or maybe a maximum capacitance that was violated on the feedback.

There are a TON of ways to screw up your PDN on a PCB. It's nominally a master's degree level subject.

by dragontamer

4/28/2026 at 3:56:28 AM

Some small switching regulators go into a low power mode when the output current goes below a threshold. The frequency drops to some "hovering just above zero" level. I've had to artificially load a power supply, to get it to be stable, e.g., with a shunt resistor. Naturally, that's inefficient, so it goes onto the TODO list to improve the design.

by analog31

4/28/2026 at 6:21:19 AM

1.5 Vpp ripple measured on a 40 MHz scope - when the waveform is 50 MHz according to him...

by elch

4/28/2026 at 4:57:09 AM

decoupling is a real issue, but I think you are right in this case.

by boznz

4/28/2026 at 4:53:35 PM

I think the author's analysis of the problem is off. He writes about ripple from the regulator:

> This switching causes ripples in the voltage line,

But what is on the scope is not that ripple:

> Take another look at the pictures of the ripples above and notice the “M: 20ns” in the top left corner. This signifies that each vertical dotted line is 20ns apart, so the ripple you see has a frequency of something like 50MHz.

The switching regulator does not operate anywhere near 50 Mhz. Those voltage fluctuations are caused by the magnetometer itself: its own internal switching causing rapid current demand fluctuations. Or, possibly, it could be some other nearby device, in which case that device needs the decoupler (also).

This is why the decoupling capacitor addresses the problem. The purpose of the decoupling capacitor isn't to filter power supply ripple, but to provide a local, low-impedance current source that can swallow changes in current demand. That's why it's placed close to the device. It not only ensures that the device has smooth power, but also reduces the noise that it generates, protecting other devices.

by kazinator

4/28/2026 at 9:19:04 PM

I don't think you're entirely correct here. The regulator will create noise that has a fundamental frequency of 500 kHz. That we agree on. However, this 50 MHz noise can most certainly be caused by the regulator. It's critical to note that it's not a constant 50 MHz noise. It's clearly attenuating quickly and occurring sharply. If the author had zoomed out to the 500 kHz time scale, I'd bet we'd see this noise every time the switches change.

by Neywiny

4/28/2026 at 1:03:04 AM

Seems like a missed opportunity to try adding a capacitor dead-bug style onto the board to see if it cleans it up.

by oakwhiz

4/28/2026 at 1:27:04 AM

If it's really 20MHz++ noise that's screwing him, you need something faster than a through hole capacitor IMO to deal with it.

That being said, I'm not 100% convinced this is a 20MHz++ noise issue.

by dragontamer

4/28/2026 at 4:56:05 AM

The capacitor doesn't have a concept of "fast enough", it's a passive component. The signal is what determines what it does when it encounters the capacitor. Non-linearities and capacitor species aside, a good ole x7r 100nF would clean this up.

In general you can just liberally dump 100nF caps all over your pcb power traces and quash most problems like this before even knowing they exist. I joke that you make a circuit then take out your 100nF salt shaker to make it just right.

by WarmWash

4/28/2026 at 7:35:54 AM

The capacitor has a self inductance. That's why you use low self inductance capacitors with very short leads or traces in this role. 100 nF ceramics are fine, but you may actually need a 100 nF and a 10 nF side-by-side because of that inductance depending on how dirty your power line is. Fast clocked circuitry can be pretty nasty.

by jacquesm

4/29/2026 at 3:11:17 PM

> 100 nF ceramics are fine, but you may actually need a 100 nF and a 10 nF side-by-side because of that inductance depending on how dirty your power line is.

Capacitance value is essentially irrelevant to inductance. The thing that dictates inductance of a decoupling capacitor is essentially only the package size. The way to fix that is to use smaller (physical) sized components. The only reason it may be related is that some larger values of capacitance physically can't fit into tiny package sizes. For 100nF, you have essentially no restrictions though. 0201(i) are easy to find in that value.

by Kirby64

4/30/2026 at 12:03:38 AM

That's fair, I was thinking of hole-through components and I should probably stop doing that in 2026... But: if we're being pedantic: it isn't the physical size as much as it is the loop area that the current travels through, and that doesn't depend so much on the size of the package as on how the package is constructed. Low ESR caps such as IDC or LGA type caps will do better than other types even if the physical size is identical. Lead length also still matters, whether physical leads or length of the traces connecting the cap to the device and these should be kept as short as possible.

by jacquesm

4/28/2026 at 6:18:19 AM

Look up parasitic inductance.

Through hole parts cap out at maybe low MHz. Many electrolytic caps frankly cannot effectively decouple signals above 100s of kHz even. Above that value, capacitors become inductors due to lead lengths, parasitic resistance, and other details.

To make capacitors work faster, we make them smaller and smaller. Surface Mount Caps are the only way to reach 20MHz++ decoupling speeds, and you need crazier tricks if you need additional decoupling beyond that frequency.

by dragontamer

4/28/2026 at 1:34:01 PM

Yes, but we are splitting hairs at that point. The transient spike is a high impedance voltage that is tripping the high impedance internal protection circuitry of the magnetometer. So whether we have 20mOhms of capacitive decoupling or 500mOhms of inductive decoupling, both are better than the infinite impedance of nothing there.

We're not building a precision filter, were cutting the paws off of a paper tiger. No need to let perfect be the enemy of good.

by WarmWash

4/28/2026 at 9:14:26 PM

This is a circuit with a switching regulator that is, presumably, stabilized with something on the order of a 10uH inductor + 22uF capacitor.

So from my perspective, increasing the capacitance from 22uF on that output line to 22.1uF with a 100nF cap will likely do jack diddly shit.

It is far more likely that, ex, the author of this post screwed up the regulator design. Ex: did the author mistakenly think that more capacitance is better-er and stick a 100uF cap there, blowing out the phase margin of the feedback of the switching regulator?

Was the inductor properly sized? Not just inductance but also saturation current and internal resistance?

by dragontamer

4/28/2026 at 3:47:36 AM

It's an easy test though and it can be an SMD component and some PUR-coated magnet wire or 30 awg single stranded kynar hookup wire.

Use a small amount of glue from a hot glue gun to fixate it when done, or epoxy if that's your thing. Avoid cyanoacrylate. Not always needed but I imagine a drone moves around alot.

Bodge wiring is a good skill to acquire - PCBs will not always be perfect. Maybe practice on something else first?

by sebcat

4/28/2026 at 4:18:26 AM

True.

I have a bunch of through-hole parts for these sorts of situations. There are plenty of small through-hole ceramics that have leads if you really want to go there.

https://www.digikey.com/en/products/detail/vishay-beyschlag-...

Like this or something similar.

by dragontamer

4/28/2026 at 7:37:12 AM

I've seen piggy backed decoupling caps straddling chips on some pretty fancy hardware. This lesson is re-learned quite frequently ;)

by jacquesm

4/28/2026 at 7:18:24 AM

> If it's really 20MHz++ noise that's screwing him, you need something faster than a through hole capacitor IMO to deal with it.

That's always worked well enough in the past.

by ErroneousBosh

4/28/2026 at 7:30:47 AM

That's because you weren't dealing with 20MHz noise.

Hobbyists are not dealing with 20MHz noise issues. Period. And if you are actually crazy enough to deal with high frequency circuits like that, you would well know that the land of through hole designs is simply insufficient, and that you are probably somewhere with some 0402 capacitors and some tweezers right now.

by dragontamer

4/28/2026 at 9:52:55 AM

> That's because you weren't dealing with 20MHz noise.

That is just straight up not correct

by PunchyHamster

4/28/2026 at 7:40:11 AM

> Hobbyists are not dealing with 20MHz noise issues.

It happens. Not often, but it does happen and it depends on the hobbyist and what they're up to (but you won't be sticking that together on a breadboard). Also: if you start using HCT, AHC or even G parts where you don't really need them it can happen to you in places where you don't normally expect it. Those things have crazy fast rise times.

by jacquesm

4/28/2026 at 7:57:38 AM

Real talk: 6 layer oshpark is cheap enough for a hobbyist and there are a bunch of 500MHz / DDR2 parts that can be laid out. Like 0.8mm pitch BGAs can fit and breakout.

So yeah. Hobbyists can go here. But here be dragons!!

Nonetheless, I continue to assert that typical hobbyists are making mistakes at 100kHz region rather than the 100MHz region.

by dragontamer

4/28/2026 at 8:10:59 AM

That's fair. It's just that I have seen some hobbyists doing the most insane stuff and eventually getting it to work. Some HAMs for instance have pretty extreme skills and it is not their profession, they just do it because they like it, not because they get paid.

And in many of those cases their skills are hard capped by their budget for test gear and simulation software rather than by their actual ability. Keep in mind that until not that long ago anything above 1 G was fair game because 'nobody does anything there anyway' and so HAMs and radio astronomers were pretty much the only ones with experience in that region.

by jacquesm

4/28/2026 at 10:09:36 PM

Or analogue. 20MHz is basically only just above audio. You can amplify it with a cheap jellybean opamp that requires no particular care to use.

by ErroneousBosh

4/28/2026 at 11:05:35 PM

Which one?

MCP6002 jellybean is GBP of 1MHz. Most "jellybean" OpAmps I know cap out at 10MHz GBWP (aka: a useless 10x gain at 1 MHz).

LM358B is 1.2 MHz GBWP or even 700kHz depending on the design. Magnitudes away from 20MHz especially when you want more than 1.0x gain.

If you want even 10x gain (aka around 10% error), you might suffice with 200MHz GBWP at 20MHz. Or maybe get a nice ADC and just go all digital given today's equipment...

Come on man. Typical "high speed" OpAmps are like 100MHz GBWP or less... correlating to only 5x gain at 20MHz. This sort of stuff is well outside "jellybean" amps. And I'm not even sure if a 100MHz amp is very effective at 20MHz.

by dragontamer

4/29/2026 at 8:46:04 AM

LT1812 is my weapon of choice for ultra low RF stuff (think Tayloe mixer frontends). Readily available, pennies to buy, reasonably flat to about 20MHz although THD is getting a little rough up there, possibly because I'm using it wrong.

They cost pennies.

by ErroneousBosh

4/29/2026 at 4:29:07 PM

https://www.digikey.com/en/products/detail/analog-devices-in...

Looks like they're closer to $3+? Like this is more expensive than a lot of microcontrollers for just one OpAmp.

I wouldn't call any Analog Devices / Linear Technologies parts to be a jellybean. Jellybean means matching common specs that any manufacturer can do.

But at $3 per chip, that's very far away from jellybean status. And AD / LT devices are known for high quality that no one else replicates.

> although THD is getting a little rough up there

Yeah, because a 100MHz high speed OpAmps only has 5x gain at 20MHz. So your error is now well in excess of like 20% (best case) or probably way way worse errors in practice.

As I said earlier: Im not even convinced that 100MHz OpAmps have the GBWP to effectively operate on 20MHz signals. You need more GBWP than that to be comfortable.

by dragontamer

4/28/2026 at 3:32:18 PM

> Hobbyists are not dealing with 20MHz noise issues.

What makes you think that?

Edit: FWIW I consider 20MHz to be basically audio.

by ErroneousBosh

4/28/2026 at 9:51:38 AM

you can dead bug SMD caps

by PunchyHamster

4/28/2026 at 10:43:18 AM

To makers that want to play and learn with power converters I recommend you:

- Test the converter at various points of load (when prototiping keep some 0ohm resistor/jumper for attaching a resistor load or electronic load).

- When you have to measure things, look around app notes/white papers of manufacturers, you will usually find practical actionable info and some examples. Doing proper measurements is really a discipline of its own, but for low frequency you can get far with the basics of craftsman/rule of thumb engineering. [0] [1]

For example the author here in the videos is mostly measuring the inductance loop between the positive of the rail and wherever ground is (we cannot even see where the osc negative is??) and how this particular loop responds to a cap, not the real bus.

[0] https://www.analog.com/en/resources/app-notes/an-1144.html

[1] https://www.richtek.com/Design%20Support/Technical%20Documen...

by frangonf

4/28/2026 at 4:05:16 AM

Meta; typo in title, should be "learNEd".

by unwind

4/28/2026 at 7:05:37 AM

Quality *Learing* Center 1-800-FRAUD

by xaxfixho

4/28/2026 at 5:36:04 AM

If getting a cap on the input of the magnetometer is too challenging, a ferrite bead on the output of the caps fed by the switching supply might also do the trick.

You could also try just sticking a 100n and 10n across the smps output too.

by WarmWash

4/28/2026 at 9:44:00 AM

Datasheet shows 2 (which is a bit unusual, one for VDD and one for VDDIO soooo very much "RTFM" problem

by PunchyHamster

4/28/2026 at 7:26:06 AM

leared = learned ? The O'Reilly book "Designing Embedded Systems" covers this pretty well with a story very similar to yours. Great to be able to learn something new.

by kreelman

4/28/2026 at 6:58:26 AM

The first time I saw a complex number used with units of resistance, I was like, huh?

by themafia

4/28/2026 at 8:33:37 AM

> How I leared what radial magnetic emissions are, the hard way

Another lesson waiting in the wings from mounting a magnetometer in plane and right next to four BLCD motors, lmao.

by moffkalast